How To Replace Steering Cable On Boat

As you spend more fourth dimension out on the water, you may notice that steering your boat has started to experience different, more stiff. Every bit steering cables age, they can go less responsive. Steering components are a very of import function of your boat and damaged or old cables can lead to trouble while out on the lake. So what is a boat possessor to do? I will comprehend both steering cable maintenance and boat steering cablevision replacement in this commodity.

Steering Cable Maintenance

Proper inspection of your steering cable at least two to three times per season is very important. Inspection should include looking at the cable jacket for signs of harm such as cracks and cuts. Also, look closely at both ends of the cable and inspect the surrounding hardware for corrosion, wear or rust. Adjacent, check to see if the cable is hard to motion.

If y'all discover the cable has any of the in a higher place harm or is difficult to move, supervene upon your parts immediately to avert dangerous situations while out on your boat. Since damaged cables cannot exist repaired, I volition now cover how to replace your steering cable.

Replacing your Steering Cable

Replacing your boat steering cablevision is a job that can be done on your ain if you are a do-it-yourselfer. If you read this article and decide the task is all-time left to the professionals, contact united states of america and we will be happy to install a boat steering cable for you. I will encompass mechanical boat steering cablevision replacement in this article.

1. Remove Your Boat Steering Cable

Removing your steering cable is relatively easy. Just disconnect the cable from the steering helm and from the engine using a wrench to loosen bolts that are holding it. Next, detect a rope that will exist used to aid you lot in pulling the cable back through the boat. Tie a rope to the helm end of the cable then pull the cablevision through from the engine cease. Accept your time pulling the cable to foreclose impairment to the wiring harness or control box. Go out the rope where the cable was located as yous volition use this to pull the cable back through to the captain when you install the new cable.

Once you have the cablevision out, you will need to locate your function number for replacement. Part numbers are usually written on the casing. Generally the last two numbers of your role number indicate the length of your cable. If you lot cannot find your role number you will need to measure your cable.

2. Measure the Cable

If you do not discover a role number on your old cable, we will help you lot measure it to become the correct replacement. Simply measure the cablevision casing as it is laid out flat. Measure nut to nut and so to that measurement, add together 24″ and round up to the next foot. Steering cables are sold by the foot so in that location is a need to round up to become the appropriate length.

Once yous have your measurement or your function #, club your steering cable and then wait by the door for UPS to bring your cable to yous. If you don't desire to wait for delivery, caput on down to our Kansas Metropolis boat parts store. Bring your old cable with you and so we can double check your measurements. As they say "measure out twice…".

If y'all are not in the Kansas Metropolis area, you can even so shop with us online or over the phone. We proudly carry Seastar / Teleflex brand steering cables, the almost pop steering cable available.

iii. Install your Cable

Now for the final role. Installing your cable is straight forrard so long as you kept your rope in place. Locate the rope you used to pull the onetime cable out. Starting a the engine terminate, necktie the captain end of your new cable to the rope and gently pull the from the helm side of the boat until you lot have the cable all the way through. Now that the cablevision is in place, bolt information technology to the helm and to the engine making sure that you have tight connections. When installing the cable, be sure non to make tight angles or kink the cable as doing so tin cause damage.

You will also need to attach the telescoping ram to the engine. The tube should be completely clean. Adjacent, utilize marine grease to grease the outside of the tube and inner telescoping ram.

Finally, test your steering wheel looking for tightness or excessive play before y'all take your boat back out on the water. As e'er, consult your owners manual before doing repairs. If you lot have whatever questions or are unsure of these instructions, please find a factory certified marine shop to assistance yous. Spending a few extra bucks upwardly front end and allowing the experts to help may keep your family safe out on the water.

Source: https://www.boatengine.com/steering-cable-replacement-guide/